blob: 2758eae7b6a95d913912bf2824f9bdf3b70d1a4e (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
#!/bin/bash
# scsi_satl
#
# Script to test compliance of SCSI commands on a SCSI to ATA
# Transaltion (SAT) Layer (SATL). This scripts was compiled using
# sat-r09.pdf found at www.t10.org .
# The vintage is SPC-3 and SPC-4 (see www.t10.org).
#
# Coverage:
# Command SATL notes
# -------------------------------------------------------
# INQUIRY (standard)
# INQUIRY (VPD: 0)
# INQUIRY (VPD: 0x83) Device identification VPD page
# INQUIRY (VPD: 0x89) ATA Information VPD page
# REPORT LUNS SPC-3, SPC-4 (hardly mentioned in sat-r08c)
# TEST UNIT READY
# REQUEST SENSE
# SEND DIAGNOSTIC default self test
# MODE SENSE(10) draft unclear which mode pages, so ask for all
# ATA PASS THROUGH(16) send IDENTIFY DEVICE command. Assume non-packet
# device, if packet device add "-p" option
#
# This script uses utilities from sg3_utils package (version
# 1.22 or later) and sdparm (version 0.99 or later)
#
# Douglas Gilbert 20061230
quiet=0
log=0
file_err=0
inv_opcode=0
illeg_req=0
not_ready=0
medium=0
other_err=0
recovered=0
sanity=0
syntax=0
timeout=0
unit_attention=0
aborted_command=0
total_err=0
usage()
{
echo "Usage: scsi_satl [-h] [-L] [-q] <device>"
echo " where: -h, --help print usage message"
echo " -L, --log append stderr to 'scsi_satl.err'"
echo " -q, --quiet suppress some output"
echo ""
echo "Check <device> for SCSI to ATA Translation Layer (SATL) support"
}
if (( $# < 1 ))
then
usage
exit 1
fi
# opt=$1
# echo ${opt##-*}
opt="$1"
while test ! -z "$opt" -a -z "${opt##-*}"; do
opt=${opt#-}
case "$opt" in
h|-help) usage ; exit 1 ;;
L|-log) let log=$log+1 ;;
q|-quiet) let quiet=$quiet+1 ;;
*) echo "Unknown option: -$opt " ; exit 1 ;;
esac
shift
opt="$1"
done
for command in "sg_inq" "sg_vpd" "sg_vpd -p di" "sg_vpd -p ai" "sg_luns" \
"sg_turs" "sg_requests -s" "sg_senddiag -t" "sg_modes -a" \
"sg_sat_identify"
do
if [ $quiet -eq 0 ]
then echo "$command" $1
fi
if [ $log -eq 0 ]
then
$command $1 > /dev/null 2>> /dev/null
else
$command $1 > /dev/null 2>> scsi_satl.err
fi
res=$?
case "$res" in
0) ;;
1) echo " syntax error" ; let syntax=$syntax+1 ;;
2) echo " not ready" ; let not_ready=$not_ready+1 ;;
3) echo " medium error" ; let medium=$medium+1 ;;
5) echo " illegal request, general" ; let illeg_req=$illeg_req+1 ;;
6) echo " unit attention" ; let unit_attention=$unit_attention+1 ;;
9) echo " illegal request, invalid opcode" ; let inv_opcode=$inv_opcode+1 ;;
11) echo " aborted command" ; let aborted_command=$aborted_command+1 ;;
15) echo " file error with $1 " ; let file_err=$file_err+1 ;;
20) echo " no sense" ; let other_err=$other_err+1 ;;
21) echo " recovered error" ; let recovered_err=$recovered_err+1 ;;
33) echo " timeout" ; let timeout=$timeout+1 ;;
97) echo " response fails sanity" ; let sanity=$sanity+1 ;;
98) echo " other SCSI error" ; let other_err=$other_err+1 ;;
99) echo " other error" ; let other_err=$other_err+1 ;;
*) echo " unknown exit status for sg_inq: $res" ; let other_err=$other_err+1 ;;
esac
done
echo ""
let total_bad_err=$file_err+$inv_opcode+$illeg_req+$medium+$aborted_command
let total_bad_err+=$other_err+$recovered+$sanity+$syntax+$timeout
let total_allow_err=$not_ready+$unit_attention
echo "total number of bad errors: $total_bad_err "
if [ $total_allow_err -gt 0 ]
then
echo "total number of allowable errors: $total_allow_err "
fi
exit $total_bad_err
|
