1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
|
Source: sg3-utils
Section: admin
Priority: optional
Maintainer: Eric Schwartz (Skif) <emschwar@debian.org>
Build-Depends: debhelper (>> 4.0.0), chrpath, libtool
Standards-Version: 3.7.2
Package: sg3-utils
Architecture: any
Depends: ${shlibs:Depends}
Conflicts: sg-utils, cdwrite
Replaces: sg-utils
Description: Collection of Linux utilities for devices that use the
SCSI command set. See the README, CHANGELOG and COVERAGE files.
.
Requires the linux kernel 2.4 series or later. In the 2.4 series
SCSI generic device names (e.g. /dev/sg0) must be used. In the 2.6
series other device names may be used as well (e.g. /dev/sda).
.
The package includes:
* sg_dd - a variant of 'dd' that works at the SCSI command level
* sg_emc_trespass - vendor specific for Clariion hardware
* sg_format - format SCSI disks
* sg_get_config - get features and profiles of MMC devices
* sg_ident - report and set device identifiers
* sginfo - a re-porting of the 'scsiinfo' program, updated
* sg_inq - a utility for poking around with the SCSI INQUIRY command
* sg_logs - prints out log sense pages
* sg_luns - prints out REPORT LUNS response
* sg_map - shows the mapping between SCSI devices and sg devices
* sg_map26 - map primary device node and generic node (lk 2.6 only)
* sgm_dd - like sg_dd, but uses mmap()'d IO
* sg_modes - prints out mode sense pages
* sg_opcodes - reports supported opcodes and task management fcns
* sgp_dd - like sg_dd, only multithreaded
* sg_persist - accesses the Persistent Reservation In and Out commands
* sg_prevent - issues PREVENT ALLOW MEDIUM REMOVAL command (MMC + SSC)
* sg_rbuf - tests SCSI bus speed
* sg_rdac - vendor specific for RDAC hardware
* sg_read - reads multiple blocks, useful for timing
* sg_read_buffer - READ BUFFER
* sg_read_long - read a "long" block from the given device
* sg_readcap - prints the output of a READ CAPACITY command
* sg_reassign - issues a REASSIGN BLOCKS command (map out bad sectors)
* sg_requests - issues a REQUEST SENSE command (event polling)
* sg_reset - exercises SCSI device/bus/host reset capability
* sg_rmsn - READ SERIAL SERIAL NUMBER
* sg_rtpg - REPORT TARGET PORT GROUPS
* sg_sat_identify - ATA IDENTIFY (PACKET) DEVICE via SATL
* sg_scan - displays the SCSI bus on stdout
* sg_senddiag - runs SCSI self tests
* sg_ses - fetches status and send control to a SES device
* sg_start - spins up (or down) disks and optical drives
* sg_sync - issues a SYNCHRONIZE CACHE command
* sg_test_rwbuf - tests the SCSI host adapter
* sg_turs - execute a TEST UNIT READY command on the given device
* sg_verify - issues VERIFY command on SCSI disks
* sg_vpd - utility for decoding VPD pages
* sg_write_buffer - WRITE BUFFER, may be used to load firmware
* sg_write_long - write a "long" block to the given device
* sg_wr_mode - low level utility to change mode pages
.
It also includes source code for some example programs that demonstrate
how to use the scsi generic driver.
Package: libsgutils1
Section: libs
Depends: ${shlibs:Depends}
Architecture: any
Recommends: sg3-utils
Description: Utilities for working with generic SCSI devices (shared libraries)
This package contains the shared libraries that allow other programs to use it.
Package: libsgutils1-dev
Section: devel
Architecture: any
Depends: libsgutils1, ${shlibs:Depends}
Recommends: sg3-utils
Description: Utilities for working with generic SCSI devices (developer files)
This package contains the <scsi/sg_cmds.h> , <scsi/sg_lib.h> ,
<scsi/sg_linux_inc.h> and <scsi/sg_io_linux.h> header files, the
/usr/lib/libsgutils.a static library and other assorted development tidbits.
|
