blob: d0da57099d9da29fca55c488896c4af4a77580e9 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
|
Introduction
============
The FreeBSD port of sg3_utils contains those utilities that are _not_
specific to Linux. In some cases the FreeBSD camcontrol command supplies
similar functionality; for example 'sg_map' is similar to
'camcontrol devlist'.
The dd variants from the sg3_utils package (e.g. sg_dd) rely on too many
Linux idiosyncracies to be easily ported. A new package called 'ddpt'
contains a utility with similar functionality to sg_dd and ddpt is available
for FreeBSD.
Supported Utilities
===================
Here is a list of utilities that have been ported:
sg_format
sg_get_config
sg_get_lba_status
sg_ident
sg_inq [dropped ATA IDENTIFY DEVICE capability]
sg_logs
sg_luns
sg_modes
sg_opcodes
sg_persist
sg_prevent
sg_raw
sg_rdac
sg_read_block_limits
sg_read_buffer
sg_read_long
sg_readcap
sg_reassign
sg_requests
sg_rmsn
sg_rtpg
sg_safte
sg_sat_identify
sg_sat_phy_event
sg_sat_set_features
sg_senddiag
sg_ses
sg_start
sg_stpg
sg_sync
sg_turs
sg_verify
sg_unmap
sg_vpd
sg_wr_mode
sg_write_buffer
sg_write_long
sg_write_same
Most utility names are indicative of the main SCSI command
that they execute. Some utilities are slightly higher level, for
example sg_ses fetches SCSI Enclosure Services (SES) status pages and
can send control pages. Each utility has a man page (placed in
section 8). An overview of sg3_utils can be found at:
http://sg.danny.cz/sg/sg3_utils.html .
A copy of the "sg3_utils.html" file is in the "doc" subdirectory.
The executables and library can be built from the source code in
the tarball and installed with the familiar
"./configure ; make ; make install" sequence. If this fails try
running the "./autogen.sh" script prior to that sequence. There
are generic instruction on configure and friend in the INSTALL file.
Some man pages have examples which use linux device names which
hopefully will not confuse the FreeBSD users.
Device naming
=============
In FreeBSD disks have block names like '/dev/da0' with a corresponding
pass-through device name like '/dev/pass0'. Use this command
"camcontrol devlist" to see that SCSI devices available.
Details
=======
Most of the ported utilities listed above use SCSI command functions
declared in sg_cmds_*.h headers . Those SCSI command functions are
implemented in the corresponding ".c" files. The ".c" files pass SCSI
commands to the host operating system via an interface declared in sg_pt.h .
There are currently five implementations of that interface depending on
the host operating system:
- sg_pt_linux.c
- sg_pt_freebsd.c
- sg_pt_osf1.c [Tru64]
- sg_pt_win32.c
- sg_pt_solaris.c
The sg_pt_freebsd.c file uses the FreeBSD CAM SCSI pass through mechanism.
Hence only FreeBSD device nodes that support CAM can be used. These can be
viewed with the "camcontrol devlist" command. To access ATAPI devices (e.g.
ATAPI DVD drives) the kernel may need to be configured with the "atapicam"
device.
FreeBSD 8.0 is the most recent version of FreeBSD tested with these
utilities.
Doug Gilbert
10th April 2010
|
