1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
Command coverage
================
The following table lists SCSI commands in alphabetical order on the
left and the sg3_utils utilities that implement invocations of them
on the right. The second table lists supported ATA commands.
SCSI command sg3_utils utilities that use this SCSI command
------------ -------------------------------------------------
ATA COMMAND PASS-THROUGH(16) sg_sat_identify, sg_sat_set_features,
sg_sat_phy_event, ++
[sg_sat_chk_power, sg__sat_identify,
sg__sat_set_features, sg_sat_smart_rd_data
(previous four in the examples directory)]
ATA COMMAND PASS-THROUGH(12) sg_sat_identify, ++
GET CONFIGURATION sg_get_config, ++
GET LBA STATUS sg_get_lba_status, ++
INQUIRY sg_dd, sg_format, sg_inq, sginfo,
sg_logs, sg_map('-i'), sg_modes, sg_opcodes,
sg_persist, sg_scan, sg_ses, sg_vpd ++
FORMAT UNIT sg_format, ++
LOG SELECT sg_logs('-r' or '-select'), ++
LOG SENSE sg_logs, ++
MODE SELECT(6) sg_wr_mode, sginfo, sg_format,
sg_emc_trespass, sg_rdac, ++
MODE SELECT(10) sg_wr_mode, sginfo, sg_format,
sg_emc_trespass, sg_rdac, ++
MODE SENSE(6) sg_modes, sg_wr_mode, sginfo, sg_format,
sg_senddiag('-e'), sg_rdac, ++
MODE SENSE(10) sg_modes, sg_wr_mode, sginfo, sg_format,
sg_senddiag('-e'), sg_rdac, ++
PERSISTENT RESERVE IN sg_persist, ++
PERSISTENT RESERVE OUT sg_persist, ++
PREVENT ALLOW MEDIUM REMOVAL sg_prevent, ++
READ(6) sg_dd, sgm_dd, sgp_dd, sg_read
READ(10) sg_dd, sgm_dd, sgp_dd, sg_read
READ(12) sg_dd, sgm_dd, sgp_dd, sg_read
READ(16) sg_dd, sgm_dd, sgp_dd, sg_read
READ BLOCK LIMITS sg_read_block_limits, ++
READ BUFFER sg_rbuf, sg_test_rwbuf, sg_read_buffer, sg_safte, ++
READ CAPACITY(10) sg_readcap, sg_dd, sgm_dd, sgp_dd, sg_format, ++
READ CAPACITY(16) sg_readcap, sg_dd, sgm_dd, sgp_dd, sg_format, ++
READ DEFECT(10) sginfo('-d' or '-G'), sg_reassign('-g'), ++
READ DEFECT(12) sginfo('-d' or '-G')
READ LONG (10) sg_read_long, sg_dd, ++
READ LONG (16) sg_read_long, ++
READ MEDIA SERIAL NUMBER sg_rmsn, ++
REASSIGN BLOCKS sg_reassign, ++
RECEIVE DIAGNOSTIC sg_senddiag, sg_ses, ++
REPORT IDENTIFYING INFORMATION sg_ident, ++ (2)
REPORT LUNS sg_luns, ++
REPORT REFERRALS sg_referrals, ++
REPORT SUPPORTED OPERATION CODES sg_opcodes
REPORT SUPPORTED TASK MANAGEMENT FUNCTIONS sg_opcodes
REPORT TARGET PORT GROUPS sg_rtpg, sg_stpg ++
REQUEST SENSE sg_requests, ++
SANITIZE sg_sanitize
SEND DIAGNOSTIC sg_senddiag, sg_ses, ++
SET IDENTIFYING INFORMATION sg_ident, ++ (3)
SET TARGET PORT GROUPS sg_stpg, ++
START STOP sg_start, ++
SYNCHRONIZE CACHE(10) sg_sync, sg_dd, sgm_dd, sgp_dd, ++
TEST UNIT READY sg_turs, sg_format, ++
UNMAP sg_unmap, ++
VERIFY(10) sg_verify, ++
VERIFY(16) sg_verify, ++
WRITE(6) sg_dd, sgm_dd, sgp_dd
WRITE(10) sg_dd, sgm_dd, sgp_dd
WRITE(12) sg_dd, sgm_dd, sgp_dd
WRITE(16) sg_dd, sgm_dd, sgp_dd
WRITE BUFFER sg_test_rwbuf, sg_write_buffer, ++
WRITE LONG(10) sg_write_long, ++
WRITE LONG(16) sg_write_long, ++
WRITE SAME(10) sg_write_same
WRITE SAME(16) sg_write_same
WRITE SAME(32) sg_write_same
<most commands> sg_raw
ATA command sg3_utils utilities that use this SCSI command
----------- ----------------------------------------------
CHECK POWER MODE examples/sg_sat_chk_power
IDENTIFY DEVICE sg_inq, sg_scan, sg_sat_identify,
examples/sg__sat_identify
IDENTIFY PACKET DEVICE sg_inq, sg_sat_identify,
examples/sg__sat_identify
READ LOG EXT sg_sat_phy_event, examples/sg__sat_phy_event
SET FEATURES sg_sat_set_features
examples/sg__sat_set_features
SMART READ DATA examples/sg_sat_smart_rd_data
++ command wrapper found in sg_cmds_basic.c, sg_cmds_mmc.c or
sg_cmds_extra.c for this command
(2) this command was known as REPORT DEVICE IDENTIFIER prior to spc4r07
(3) this command was known as SET DEVICE IDENTIFIER prior to spc4r07
Douglas Gilbert
24th February 2012
|
