diff options
Diffstat (limited to 'lib/sg_lib_data.c')
| -rw-r--r-- | lib/sg_lib_data.c | 177 |
1 files changed, 176 insertions, 1 deletions
diff --git a/lib/sg_lib_data.c b/lib/sg_lib_data.c index 76964d8c..b6362a50 100644 --- a/lib/sg_lib_data.c +++ b/lib/sg_lib_data.c @@ -17,7 +17,7 @@ #endif -const char * sg_lib_version_str = "2.34 20171219";/* spc5r17, sbc4r15 */ +const char * sg_lib_version_str = "2.35 20171227";/* spc5r17, sbc4r15 */ /* indexed by pdt; those that map to own index do not decay */ @@ -1506,3 +1506,178 @@ struct sg_lib_value_name_t sg_lib_scsi_feature_sets[] = {SCSI_FS_SBC_DRIVE_MAINT_2016, PDT_DISK, "Drive maintenance 2016"}, {0x0, 0, NULL}, /* 0x0 is reserved sfs; trailing sentinel */ }; + +/* .value is completion queue's DW3 as follows: ((DW3 >> 17) & 0x3ff) + * .peri_dev_type is an index for the sg_lib_scsi_status_sense_arr[] + * .name is taken from NVMe 1.3a document, section 4.6.1.2.1 with less + * capitalization. + * NVMe term bits 31:17 of DW3 in the completion field as the "Status + * Field" (SF). Bit 31 is "Do not retry" (DNR) and bit 30 is "More" (M). + * Bits 29:28 are reserved, bit 27:25 are the "Status Code Type" (SCT) + * and bits 24:17 are the Status Code (SC). This table is in ascending + * order of its .value field so a binary search could be done on it. */ +#ifdef SG_SCSI_STRINGS +struct sg_lib_value_name_t sg_lib_nvme_cmd_status_arr[] = +{ + /* Generic command status values, Status Code Type (SCT): 0h + * Lowest 8 bits are the Status Code (SC), in this case: + * 00h - 7Fh: Applicable to Admin Command Set, or across multiple + * command sets + * 80h - BFh: I/O Command Set Specific status codes + * c0h - FFh: I/O Vendor Specific status codes */ + {0x0, 0, "Successful completion"}, + {0x1, 1, "Invalid command opcode"}, + {0x2, 2, "Invalid field in command"}, + {0x3, 2, "Command id conflict"}, + {0x4, 3, "Data transfer error"}, + {0x5, 4, "Command aborted due to power loss notication"}, + {0x6, 5, "Internal error"}, + {0x7, 6, "Command abort requested"}, + {0x8, 6, "Command aborted due to SQ deletion"}, + {0x9, 6, "Command aborted due to failed fused command"}, + {0xa, 6, "Command aborted due to missing fused command"}, + {0xb, 7, "Invalid namespace or format"}, + {0xc, 5, "Command sequence error"}, + {0xd, 5, "Invalid SGL segment descriptor"}, + {0xe, 5, "Invalid number of SGL descriptors"}, + {0xf, 5, "Data SGL length invalid"}, + {0x10, 5, "Matadata SGL length invalid"}, + {0x11, 5, "SGL descriptor type invalid"}, + {0x12, 5, "Invalid use of controller memory buffer"}, + {0x13, 5, "PRP offset invalid"}, + {0x14, 2, "Atomic write unit exceeded"}, + {0x15, 8, "Operation denied"}, + {0x16, 5, "SGL offset invalid"}, + {0x17, 5, "Reserved [0x17]"}, + {0x18, 5, "Host identifier inconsistent format"}, + {0x19, 5, "Keep alive timeout expired"}, + {0x1a, 5, "Keep alive timeout invalid"}, + {0x1b, 6, "Command aborted due to Preempt and Abort"}, + {0x1c, 10, "Sanitize failed"}, + {0x1d, 11, "Sanitize in progress"}, + {0x1e, 5, "SGL data block granularity invalid"}, + {0x1f, 5, "Command not supported for queue in CMB"}, + + /* Generic command status values, NVM (I/O) Command Set */ + {0x80, 12, "LBA out of range"}, + {0x81, 3, "Capacity exceeded"}, + {0x82, 13, "Namespace not ready"}, + {0x83, 14, "Reservation conflict"}, + {0x84, 15, "Format in progress"}, + /* 0xc0 - 0xff: vendor specific */ + + /* Command specific status values, Status Code Type (SCT): 1h */ + {0x100, 5, "Completion queue invalid"}, + {0x101, 5, "Invalid queue identifier"}, + {0x102, 5, "Invalid queue size"}, + {0x103, 5, "Abort command limit exceeded"}, + {0x104, 5, "Reserved [0x104]"}, + {0x105, 5, "Asynchronous event request limit exceeded"}, + {0x106, 5, "Invalid firmware slot"}, + {0x107, 5, "Invalid firmware image"}, + {0x108, 5, "Invalid interrupt vector"}, + {0x109, 5, "Invalid log page"}, + {0x10a,16, "Invalid format"}, + {0x10b, 5, "Firmware activation requires conventional reset"}, + {0x10c, 5, "Invalid queue deletion"}, + {0x10d, 5, "Feature identifier not saveable"}, + {0x10e, 5, "Feature not changeable"}, + {0x10f, 5, "Feature not namespace specific"}, + {0x110, 5, "Firmware activation requires NVM subsystem reset"}, + {0x111, 5, "Firmware activation requires reset"}, + {0x112, 5, "Firmware activation requires maximum time violation"}, + {0x113, 5, "Firmware activation prohibited"}, + {0x114, 5, "Overlapping range"}, + {0x115, 5, "Namespace insufficient capacity"}, + {0x116, 5, "Namespace identifier unavailable"}, + {0x117, 5, "Reserved [0x107]"}, + {0x118, 5, "Namespace already attached"}, + {0x119, 5, "Namespace is private"}, + {0x11a, 5, "Namespace not attached"}, + {0x11b, 3, "Thin provisioning not supported"}, + {0x11c, 3, "Controller list invalid"}, + {0x11d,17, "Device self-test in progress"}, + {0x11e,18, "Boot partition write prohibited"}, + {0x11f, 5, "Invalid controller identifier"}, + {0x120, 5, "Invalid secondary controller state"}, + {0x121, 5, "Invalid number of controller resorces"}, + {0x122, 5, "Invalid resorce identifier"}, + + /* Command specific status values, Status Code Type (SCT): 1h + * for NVM (I/O) Command Set */ + {0x180, 2, "Conflicting attributes"}, + {0x181,19, "Invalid protection information"}, + {0x182,18, "Attempted write to read only range"}, + /* 0x1c0 - 0x1ff: vendor specific */ + + /* Media and Data Integrity error values, Status Code Type (SCT): 2h */ + {0x280,20, "Write fault"}, + {0x281,21, "Unrecovered read error"}, + {0x282,22, "End-to-end guard check error"}, + {0x283,23, "End-to-end application tag check error"}, + {0x284,24, "End-to-end reference tag check error"}, + {0x285,25, "Compare failure"}, + {0x286, 8, "Access denied"}, + {0x287,26, "Deallocated or unwritten logical block"}, + /* 0x2c0 - 0x2ff: vendor specific */ + + /* Leave this Sentinel value at end of this array */ + {0x3ff, 0, NULL}, +}; + +/* The sg_lib_nvme_cmd_status_arr[n].peri_dev_type field is an index + * to this array. It allows an NVMe status (error) value to be mapped + * to this SCSI tuple: status, sense_key, additional sense code (asc) and + * asc qualifier (ascq). For brevity SAM_STAT_CHECK_CONDITION is written + * as 0x2. */ +struct sg_lib_4tuple_u8 sg_lib_scsi_status_sense_arr[] = +{ + {SAM_STAT_GOOD, SPC_SK_NO_SENSE, 0, 0}, /* it's all good */ /* 0 */ + {SAM_STAT_CHECK_CONDITION, SPC_SK_ILLEGAL_REQUEST, 0x20, 0x0},/* opcode */ + {0x2, SPC_SK_ILLEGAL_REQUEST, 0x24, 0x0}, /* field in cdb */ + {0x2, SPC_SK_MEDIUM_ERROR, 0x0, 0x0}, + {SAM_STAT_TASK_ABORTED, SPC_SK_ABORTED_COMMAND, 0xb, 0x8}, + {0x2, SPC_SK_HARDWARE_ERROR, 0x44, 0x0}, /* internal error */ /* 5 */ + {SAM_STAT_TASK_ABORTED, SPC_SK_ABORTED_COMMAND, 0x0, 0x0}, + {0x2, SPC_SK_ILLEGAL_REQUEST, 0x20, 0x9}, /* invalid LU */ + {0x2, SPC_SK_ILLEGAL_REQUEST, 0x20, 0x2}, /* access denied */ + {0x2, SPC_SK_ILLEGAL_REQUEST, 0x2c, 0x0}, /* cmd sequence error */ + {0x2, SPC_SK_MEDIUM_ERROR, 0x31, 0x3}, /* sanitize failed */ /* 10 */ + {0x2, SPC_SK_NOT_READY, 0x4, 0x1b}, /* sanitize in progress */ + {0x2, SPC_SK_ILLEGAL_REQUEST, 0x21, 0x0}, /* LBA out of range */ + {0x2, SPC_SK_NOT_READY, 0x4, 0x0}, /* not reportable; 0x1: becoming */ + {SAM_STAT_RESERVATION_CONFLICT, 0x0, 0x0, 0x0}, + {0x2, SPC_SK_NOT_READY, 0x4, 0x4}, /* format in progress */ /* 15 */ + {0x2, SPC_SK_ILLEGAL_REQUEST, 0x31, 0x1}, /* format failed */ + {0x2, SPC_SK_NOT_READY, 0x4, 0x9}, /* self-test in progress */ + {0x2, SPC_SK_DATA_PROTECT, 0x27, 0x0}, /* write prohibited */ + {0x2, SPC_SK_ILLEGAL_REQUEST, 0x10, 0x5}, /* protection info */ + {0x2, SPC_SK_MEDIUM_ERROR, 0x3, 0x0}, /* periph dev w fault */ /* 20 */ + {0x2, SPC_SK_MEDIUM_ERROR, 0x11, 0x0}, /* unrecoc rd */ + {0x2, SPC_SK_MEDIUM_ERROR, 0x10, 0x1}, /* PI guard */ + {0x2, SPC_SK_MEDIUM_ERROR, 0x10, 0x2}, /* PI app tag */ + {0x2, SPC_SK_MEDIUM_ERROR, 0x10, 0x2}, /* PI app tag */ + {0x2, SPC_SK_MISCOMPARE, 0x1d, 0x0}, /* during verify */ /* 25 */ + {0x2, SPC_SK_MEDIUM_ERROR, 0x21, 0x6}, /* read invalid data */ + + /* Leave this Sentinel value at end of this array */ + {0xff, 0xff, 0xff, 0xff}, +}; + + +#else /* no SG_SCSI_STRINGS define in config.sys */ +struct sg_lib_value_name_t sg_lib_nvme_cmd_status_arr[] = +{ + + /* Leave this Sentinel value at end of this array */ + {0x3ff, 0, NULL}, +}; + +struct sg_lib_4tuple_u8 sg_lib_scsi_status_sense_arr[] = +{ + + /* Leave this Sentinel value at end of this array */ + {0xff, 0xff, 0xff, 0xff}, +}; + +#endif /* SG_SCSI_STRINGS */ |